SEND THE DETAILS
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We buy hospital facility chillers in San Antonio, Texas, with cash offers and upfront payment when a purchase is agreed. We handle removal, and the seller does not need to test the equipment.
From first photo to final haul, we take care of the details so you can move forward.
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We review the chiller and your site information, then make an offer. Payment is upfront.
We handle disconnects, refrigerant recovery, crane and rigging, loading, freight and hauling.
A useful value review looks at two connected questions: what equipment is being offered, and what would it take to remove it from the hospital site? We buy used hospital and other commercial or industrial chillers in San Antonio, including water-cooled and air-cooled units, and consider centrifugal, screw, and scroll machines. Capacity may range from about 20 tons to more than 2,000 tons, and we consider all refrigerants. These are review ranges, not a promise to purchase a particular unit.
A cooling ton describes capacity, not the machine’s lifting weight. The offer depends on the actual asset and project review, including available identification, known condition, included components, refrigerant information, and the removal scope. Idle and non-running equipment can be considered; you do not need to restart, test, repair, or demonstrate it. If a purchase is agreed, payment is made upfront before pickup on the agreed terms.
Begin with the manufacturer and model, serial number, capacity, and any readable equipment-plate details. Add photographs of the chiller and its surroundings, plus the number of units being offered and whether accessories or separate components are included. If information is missing or uncertain, say so rather than guessing.
Describe the known operating history and present condition, including whether the machine is idle, disconnected, incomplete, or non-running. Note any known refrigerant type or charge information if available, but do not open the circuit to find out. No test run is needed to request a review.
At a healthcare property, the route from the equipment to the loading point may pass near occupied areas or systems that need to remain in service. If applicable, explain the facility’s access windows, authorized entry process, infection-control procedures, noise limits, restricted areas, and rules for contractors. These details help define when and how the chiller work can be coordinated; they do not mean every hospital has the same restrictions.
Identify the person authorized to approve the sale and the site contact who can confirm access and work boundaries. If the building is changing hands, being vacated, or undergoing a plant upgrade, clarify which equipment belongs in the sale and the deadline or preferred removal window. Nearby chillers, piping, controls, and other plant equipment are not included unless specifically identified.
Tell us where the chiller sits: indoors, in a plant room, at grade, or on a roof. Photos from safe positions can show doors, corridors, stairs, overhead obstructions, nearby piping, and the route to a staging or truck area. Mention known limits on floor loading, ground support, truck access, clearances, or the hours when work is permitted. If dimensions or weights are documented, share them; do not estimate lifting weight from cooling capacity.
For a rooftop unit, useful details may include roof access, building height if known, parapets or overhead obstructions, and possible crane setup and staging areas. For an indoor machine, narrow doors, low ceilings, turns, or shared service corridors may shape the handling plan. Actual conditions determine whether a crane or another method is appropriate; photographs support review but do not replace site approval.
Refrigerant recovery and utility disconnects are included in the removal work we arrange and handle, with qualified personnel addressing recovery. The seller should not vent refrigerant or open the chiller’s circuit, and does not need to hire a separate recovery crew. Before work starts, the site’s authorized contact supplies accurate information, applicable rules, access, and necessary approvals, and coordinates any required isolation with the team.
Electrical, mechanical, and control connections can differ between installations. Explain what is known about connections and whether the chiller shares utilities or nearby equipment with operating systems. The work is confined to the agreed equipment scope; the facility’s boundaries and approvals matter where other plant systems must remain untouched.
We arrange and handle disconnects, rigging, crane work when needed, loading, freight, and hauling. The appropriate method depends on the actual machine, lifting points, route, clearances, ground or roof conditions, and site requirements. A proposed pickup window can be discussed after the access plan and scope are understood; timing should not be assumed before those details are confirmed.
To begin, provide the equipment identification you have, a few safe-location photographs, known condition and refrigerant details, the unit’s location within the property, and the best authorized site contact. Include any relevant access rules or project deadlines. We can use that information to review the asset and practical removal scope, then discuss whether a cash offer is appropriate. No purchase is guaranteed, and no testing, repair, restart, or seller-arranged removal is required to start the conversation.

Air-cooled or water-cooled. Centrifugal, screw or scroll. From single units to large shutdown projects, we buy industrial chillers across Texas.
Send us your chiller details and nameplate photos for a cash offer. Don’t worry if you don’t know every specification—we can start with what you have.
Call or text(614) 715-3047TEXT NAMEPLATE PHOTOS ↗Prefer email?
saleselectricalbuyers@gmail.com