SEND THE DETAILS
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We buy chillers marked R-22 in San Antonio, Texas, with cash offers and upfront payment when a purchase is agreed. We handle removal, and the seller does not need to test the equipment.
From first photo to final haul, we take care of the details so you can move forward.
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We review the chiller and your site information, then make an offer. Payment is upfront.
We handle disconnects, refrigerant recovery, crane and rigging, loading, freight and hauling.
You do not need to test, restart, repair, clean, or disconnect an R-22-marked chiller before asking us to review it. Do not vent refrigerant or open the circuit. We consider idle and non-running equipment, and a label alone does not establish what refrigerant is currently in the system.
For an initial review, share the equipment identification plate, any R-22 marking, and a few photographs. Include the manufacturer and model if readable, listed cooling capacity, known condition, and any service or conversion records you have. If a detail is missing or uncertain, say so rather than guessing.
A marking can help identify how a chiller was built or previously serviced, but the machine may have been altered, partially emptied, or left with an unknown charge. Tell us what the available records and labels say; there is no need to verify the charge yourself. We consider chillers across refrigerants and review the actual equipment and removal scope before discussing a purchase.
We buy used commercial and industrial water-cooled and air-cooled chillers, including centrifugal, screw, and scroll units. Equipment is generally within a broad range of 20 to 2,000-plus cooling tons, though suitability depends on the individual asset and project. Cooling tons measure capacity, not lifting weight, so the number on a plate is not enough to plan rigging.
Photos of the chiller in place can show useful context: its room or outdoor position, nearby equipment, doorways, overhead obstructions, and the route toward a loading area. If you know clearances or access limits, include them. The actual route may involve narrow openings, steps, low ceilings, restricted work areas, or other conditions that need review before removal is scheduled.
For a San Antonio property, we plan around the specific building and its rules rather than assuming every site has the same access or working conditions. Share applicable security procedures, permitted work hours, loading restrictions, and any known timing window. Identify equipment that must remain in place or systems that the facility needs to keep operating.
If a purchase is agreed, we coordinate appropriate refrigerant recovery with qualified personnel, along with equipment disconnects, rigging, crane work when needed, loading, freight, and hauling. The requirements depend on the chiller’s configuration, surroundings, and the facility’s procedures. We do not ask the seller to hire a recovery contractor, crane, or hauler as a condition of requesting a review.
The plan is made with the authorized site contact. The buyer is responsible for the equipment-side work; the seller or facility supplies accurate information, authorized access, site rules, and necessary approvals. If there are isolation requirements, neighboring systems, or restrictions on moving through occupied areas, flag them early so the scope can be discussed before pickup.
A cash offer depends on review of the actual chiller and project. Identification, condition, included components, known history, refrigerant information, and the work needed to remove the equipment may all be relevant. An R-22 marking does not by itself determine value or guarantee that an offer will be made. No purchase is assumed until the equipment and terms have been reviewed and agreed.
When we agree to purchase a chiller, payment is made upfront before pickup, on the agreed terms. Removal timing and access are coordinated after the equipment scope and practical site requirements are clear. If information changes—for example, the machine differs from the description—raise that before the arrangement is finalized.
Send the information you can access safely: photographs of the nameplate and refrigerant markings, overall views of the equipment, known condition, and a brief description of the route out. Add any records about refrigerant changes and note what remains uncertain. You do not have to produce a complete service history for an initial conversation.
Also tell us who can authorize access and whether the chiller is part of a larger replacement or closure schedule. We can use those details to review the asset and likely removal scope, then discuss whether a purchase makes sense. Until a plan is agreed, leave the machine and refrigerant circuit untouched; the next step is simply to share what you know.

Air-cooled or water-cooled. Centrifugal, screw or scroll. From single units to large shutdown projects, we buy industrial chillers across Texas.
Send us your chiller details and nameplate photos for a cash offer. Don’t worry if you don’t know every specification—we can start with what you have.
Call or text(614) 715-3047TEXT NAMEPLATE PHOTOS ↗Prefer email?
saleselectricalbuyers@gmail.com