SEND THE DETAILS
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We buy 1,000 to 1,999 ton chillers in El Paso, Texas, with cash offers and upfront payment when a purchase is agreed. We handle removal, and the seller does not need to test the equipment.
From first photo to final haul, we take care of the details so you can move forward.
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We review the chiller and your site information, then make an offer. Payment is upfront.
We handle disconnects, refrigerant recovery, crane and rigging, loading, freight and hauling.
Yes. We buy used industrial and commercial water-cooled and air-cooled chillers, including large-capacity units in the 1,000–1,999 ton range. Centrifugal, screw, and scroll equipment may be considered, and we review all refrigerants. An idle or non-running machine can also be discussed; it does not have to be restarted to begin a review.
Cooling tons describe capacity, not the chiller’s physical weight. For a unit this large, the distinction matters: handling and transport depend on the actual equipment, its configuration, and the route out of the property—not its capacity rating alone. A purchase is subject to reviewing the asset and the work involved, so this range does not by itself guarantee an offer.
Start with what you can confirm: the nameplate information, manufacturer and model if visible, chiller type, known refrigerant, and whether the unit is operating, idle, or incomplete. Photos of the whole machine, nearby connections, its current setting, and likely exit route can make the initial review more useful. If records or service history are available, include them; they are helpful, not a reason to delay reaching out.
Be candid about unknowns. The present charge, internal condition, configuration, and operating history may not be clear, particularly for equipment that has been out of service. Don’t run the chiller, open its refrigerant circuit, or vent refrigerant to gather information. A qualified review can establish what is needed without asking you to perform those tasks.
The offer depends on the specific asset and the project review, including the information supplied and the practical scope for removing it. Capacity is one identifying detail; condition, included components, access, and handling requirements may also matter. We can discuss a cash offer after reviewing the equipment and circumstances, but an offer is not guaranteed simply because the chiller falls within the stated tonnage range.
If a purchase is agreed, payment is made upfront before pickup, on the terms agreed with the seller. Confirm those terms, the equipment included in the sale, and the pickup scope with the authorized seller and site contact before work is scheduled. That gives both sides a clear basis for coordinating the transaction and removal.
We coordinate appropriate refrigerant recovery with qualified personnel, along with the necessary disconnects. The seller does not need to hire a recovery contractor, test the machine, repair it, restart it, or disconnect it independently. Never vent refrigerant or open a circuit to prepare the unit for sale.
Each facility has its own boundaries and procedures. The authorized site contact should identify applicable site rules, approvals, access requirements, and any operating limits around nearby equipment. If the chiller is connected to a plant that must remain in service, share what is known so the scope and timing can be coordinated around actual conditions.
We coordinate rigging, crane work when needed, loading, freight, and hauling, based on the machine and the property. The right handling plan cannot be determined from tonnage alone. It may depend on clearances, floor or ground conditions, overhead obstacles, the distance to a loading point, and whether the unit can pass through the available route. These details are reviewed for the actual site rather than assumed in advance.
For a property in El Paso, useful pickup information includes where transport vehicles may enter and stand, how crews check in, and any limits on work hours or access. Photos or a simple description of the path from the chiller to the loading area can help flag questions early. If a crane or specialized rigging may be needed, the site contact can point out relevant access and placement constraints for review.
The buyer is responsible for coordinating the equipment work. The seller and site team provide accurate information, an authorized contact, permitted access, site rules, and necessary approvals. If an upgrade or other project determines when the old chiller becomes available, share the expected timing and identify who can confirm the handoff. Pickup arrangements should be agreed before crews and transport are scheduled.
Tell us what is known, even if the details are incomplete: where the unit is, whether it is still connected, its visible identification, known condition, and any access restrictions. The next step is to submit that information and available photos for review. From there, the asset and removal scope can be discussed, with no requirement to test, repair, restart, or prepare the refrigerant circuit yourself.

Air-cooled or water-cooled. Centrifugal, screw or scroll. From single units to large shutdown projects, we buy industrial chillers across Texas.
Send us your chiller details and nameplate photos for a cash offer. Don’t worry if you don’t know every specification—we can start with what you have.
Call or text(614) 715-3047TEXT NAMEPLATE PHOTOS ↗Prefer email?
saleselectricalbuyers@gmail.com