SEND THE DETAILS
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We buy 1,000 to 1,999 ton chillers in Austin, Texas, with cash offers and upfront payment when a purchase is agreed. We handle removal, and the seller does not need to test the equipment.
From first photo to final haul, we take care of the details so you can move forward.
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We review the chiller and your site information, then make an offer. Payment is upfront.
We handle disconnects, refrigerant recovery, crane and rigging, loading, freight and hauling.
You do not need to restart, test, repair, clean, or disconnect a 1,000–1,999 ton chiller before asking us to review it. If it is idle or will not run, say so; operating condition is useful context, but a working demonstration is not a prerequisite. Do not open the refrigerant circuit or vent anything. We arrange appropriate refrigerant recovery with qualified personnel if a purchase is agreed.
For an initial review, send what is readily available: a nameplate photo, a few clear views of the unit, its location, and a brief account of known condition or history. If a detail is unknown, mark it unknown rather than estimating. We buy qualifying industrial and commercial chillers, but each unit and removal project is reviewed before an offer is made.
The 1,000–1,999 ton range describes cooling capacity. It does not tell us the chiller’s weight, dimensions, lifting points, or whether it can pass through a particular opening. Those physical details matter when planning rigging and transport, so provide manufacturer and model information where available and any documented weight or dimensions you have.
We consider water-cooled and air-cooled equipment, including centrifugal, screw, and scroll chillers, and consider all refrigerants. The installed configuration, charge, and condition are not known until information is supplied and the project is reviewed. A clear description is more useful than a confident guess about what is inside or still connected.
Photos can make the first conversation more practical. Along with close-ups of the identification plate, include a wide view showing the chiller in context and, if possible, views along the route toward an exit or loading area. Mention whether it is indoors, outdoors, on a roof, below grade, or in a restricted plant area. These are planning details, not reasons to assume the job is straightforward or impossible.
For an Austin-area site, actual building and access conditions determine the removal plan. Doorways, overhead clearance, floor transitions, neighboring equipment, occupied areas, and the available staging space may affect how a large unit can be handled. If measurements, drawings, or existing rigging records are available, they can help; do not infer lift weight from tonnage.
Identify the specific chiller being offered and tell us about controls or other components you believe are included. Also point out nearby equipment, piping, electrical gear, or plant systems that must remain in service or are outside the proposed sale. The buyer’s work is limited to the equipment and removal scope agreed between the parties; a broader decommissioning project should not be presumed included.
Tell us about known connections, shutdown boundaries, access restrictions, and the site’s required work hours or safety procedures. The authorized site contact supplies accurate information, approved access, site rules, and necessary permissions. We coordinate disconnects and removal work with that contact, rather than asking the seller to resolve the handling scope alone.
If we agree to purchase, we arrange the appropriate work for the actual site, which may include qualified refrigerant recovery, disconnects, rigging, crane work when needed, loading, freight, and hauling. Whether a crane or another handling method is appropriate depends on the unit, route, lifting requirements, and surroundings. No particular configuration or equipment is assumed before review.
The seller does not need to hire a recovery contractor, crane, rigging crew, or hauler for the buyer’s agreed removal work. The site does need to identify who can authorize access and coordinate with the work team. If the chiller is beside operating equipment or within an occupied facility, explain any boundaries that crews must respect so the plan can be discussed before scheduling.
A cash offer depends on the asset and the removal project after review; it is not guaranteed by capacity, location, or equipment type alone. Identification, known condition, completeness, access, and the work needed to remove and transport the chiller all help define the opportunity. We do not quote a fixed amount per cooling ton.
If a purchase is agreed, payment is made upfront before pickup, on the terms agreed by both sides. Before work is scheduled, confirm the unit included, the agreed terms, who has authority to sell it, and the access arrangements. That makes the equipment handoff and removal scope clear.
Gather the nameplate or model details, available photos, known operating or storage history, and any information about location, access, and included components. Send what you have for review, noting any gaps rather than filling them with assumptions. We can then discuss the specific 1,000–1,999 ton chiller, the likely removal questions, and whether an offer is appropriate. There is no need to test, restart, repair, or prepare the machine first.

Air-cooled or water-cooled. Centrifugal, screw or scroll. From single units to large shutdown projects, we buy industrial chillers across Texas.
Send us your chiller details and nameplate photos for a cash offer. Don’t worry if you don’t know every specification—we can start with what you have.
Call or text(614) 715-3047TEXT NAMEPLATE PHOTOS ↗Prefer email?
saleselectricalbuyers@gmail.com