SEND THE DETAILS
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We buy 100 to 249 ton chillers in Houston, Texas, with cash offers and upfront payment when a purchase is agreed. We handle removal, and the seller does not need to test the equipment.
From first photo to final haul, we take care of the details so you can move forward.
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We review the chiller and your site information, then make an offer. Payment is upfront.
We handle disconnects, refrigerant recovery, crane and rigging, loading, freight and hauling.
A 100-to-249-ton chiller may be offered because a replacement is planned, a process has changed, or equipment has simply been left idle. We buy used industrial and commercial water-cooled and air-cooled chillers, including centrifugal, screw, and scroll units. We consider different refrigerants and non-running equipment; a seller-run test is not a prerequisite.
For an initial review, share whatever identification is available: a nameplate photo, manufacturer and model, stated capacity, refrigerant label, and clear views of the whole machine. Add a short note on known condition and history, including anything missing or uncertain. Cooling tons describe capacity, not shipping weight, so that rating cannot establish the load for a lift or truck.
It helps to think backward from the truck. Where could a loaded vehicle wait? From that point, what route would the chiller take out of the building or yard? Then consider the final move from its present position: through a doorway, down from a roof, out of a plant room, or across an open work area. These are possibilities to describe, not features we assume about a Houston site.
Photos that show the chiller in context can make the first conversation more useful. If practical, include the route’s tight turns, doors, overhead clearance, floor transitions, and possible staging area. Approximate dimensions can help, but do not enter restricted areas or make measurements that require unsafe access. A site representative can confirm details and explain what routes are permitted.
A machine’s route may affect whether rigging can proceed in one move or needs intermediate handling. Roof position, structural limits, lifting points, nearby services, ground support, and crane placement may matter, depending on the installation. No photograph alone establishes that a lift is safe or feasible. The actual equipment and site conditions must be reviewed before a method is selected.
Tell us who can authorize access and describe any applicable work hours, check-in procedures, operating boundaries, or loading restrictions. If the chiller is near equipment that must remain in service, identify that boundary clearly. The site supplies accurate information, authorized access, site rules, and necessary approvals; we coordinate the equipment work with its authorized contact.
Identify the specific chiller being offered and mention any components you believe belong with it. If the unit is connected to shared piping, electrical service, or other operating systems, note what must remain. We arrange and handle appropriate disconnects as part of a purchase, coordinated with the site contact so equipment outside the agreed scope is protected.
Do not open refrigerant circuits or vent refrigerant to prepare for a sale. You do not need to hire a recovery contractor or restart the machine for our review. When a purchase is agreed, we arrange appropriate refrigerant recovery with qualified personnel. The present charge and refrigerant type may be unknown, so a label or records can be helpful without being a reason to guess.
A cash offer depends on the actual asset and project review, including the information available and the removal requirements. An offer is not guaranteed, and a stated tonnage alone does not determine whether a purchase will proceed or what it may be worth. Idle or non-running status does not automatically rule out consideration.
Before work begins, the seller and buyer agree on the equipment scope, access, and payment terms. If a purchase is agreed, payment is made upfront before pickup, on those agreed terms. The seller does not need to repair, test, clean, disconnect, or restart the chiller first.
After the scope and route are understood, we coordinate the appropriate removal work: refrigerant recovery, disconnects, rigging, crane work when needed, loading, freight, and hauling. Which steps apply depends on the unit and its setting. The plan should account for the path all the way to the truck, not just the lift away from the equipment pad or roof.
Before proposing a schedule, the authorized contact can flag access windows, required approvals, site safety procedures, and any operational limits. If the route, clearances, or available information change, the handling plan may need another review. This keeps the agreed equipment and work boundary clear for everyone involved.
To begin, send the available nameplate details and photographs, say whether the chiller is water-cooled or air-cooled if known, and describe its current location and condition. Include a few views of the likely route to a loading position and identify a person authorized to discuss site access. If records are incomplete, say so; do not estimate hidden specifications or claim the machine runs if you do not know.
With those basics, we can review whether the asset and removal project merit a cash offer and discuss the next steps. The decision follows the actual equipment and site review, while pickup arrangements remain subject to agreed terms and authorized access.

Air-cooled or water-cooled. Centrifugal, screw or scroll. From single units to large shutdown projects, we buy industrial chillers across Texas.
Send us your chiller details and nameplate photos for a cash offer. Don’t worry if you don’t know every specification—we can start with what you have.
Call or text(614) 715-3047TEXT NAMEPLATE PHOTOS ↗Prefer email?
saleselectricalbuyers@gmail.com