SEND THE DETAILS
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We buy warehouse chillers in Lubbock, Texas, with cash offers and upfront payment when a purchase is agreed. We handle removal, and the seller does not need to test the equipment.
From first photo to final haul, we take care of the details so you can move forward.
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We review the chiller and your site information, then make an offer. Payment is upfront.
We handle disconnects, refrigerant recovery, crane and rigging, loading, freight and hauling.
A warehouse chiller can be easy to identify and still take careful planning to remove. The useful question is how the machine can travel from its present position to a loading point and then onto a truck. It may sit on an exterior pad, in a mechanical room, on a roof, or somewhere along a warehouse service area; the actual layout determines the handling plan.
We buy used warehouse chillers in Lubbock, Texas, including water-cooled and air-cooled equipment and centrifugal, screw, and scroll units. We consider equipment generally from 20 to more than 2,000 cooling tons, across refrigerants, and will review idle or non-running machines. A cooling ton measures capacity, not the chiller’s weight, so capacity alone does not establish what lifting or transport equipment is appropriate.
For an initial review, describe the route in sequence: where the chiller stands, how it leaves that area, which doors or openings it must pass through, and where a vehicle could load it. If it is elevated or indoors, mention the access points and any known limits on openings, floors, ramps, or freight routes. Do not assume a service elevator or doorway can accommodate the unit; measurements and site approval matter.
Photos can make that route easier to understand. A wide view of the chiller, readable identification markings, and views of the exit path and potential loading area are useful. Include obstacles or shared work areas only if they are present at your facility. If details such as clearances or structural limits are unknown, say so rather than estimating.
Warehouse mechanical areas may contain pumps, controls, piping, neighboring equipment, or other assets that are not included in the proposed sale. Identify the chiller clearly and list any accessories you intend to include. Also note connections and adjacent assets that must remain undisturbed. This gives the equipment review and removal scope the same boundary.
Share the model and serial information, capacity, refrigerant marking, and known history when available. Tell us whether the unit is operating, idle, incomplete, or known to have a problem. An unknown charge or uncertain condition is useful information too: we review what is known without treating an unverified detail as fact.
You do not need to test, run, repair, restart, or demonstrate the chiller to request a review. Do not vent refrigerant or open the refrigerant circuit. Recovery is coordinated as part of the agreed work, with qualified personnel; the seller is not expected to arrange recovery independently.
Before pickup, we coordinate the appropriate recovery, utility disconnects, handling, and transport with the authorized site contact. Depending on the equipment and route, removal may involve rigging, a crane, staged loading, or other suitable methods. Those needs cannot be settled from capacity or a photograph alone; they depend on the actual machine, access, surroundings, and project review.
Tell us about relevant access procedures, working hours, security steps, loading restrictions, and any approvals required at the property. If truck staging, shared warehouse traffic, overhead conditions, or ground access could affect the route, include what you know. We arrange and handle the equipment work, rigging and hauling; the facility supplies accurate information, authorized access, site rules, and necessary approvals.
A cash offer depends on the asset and review of the actual removal project, including known condition, equipment included, and the work needed to reach and load it. An offer is not guaranteed, and not every chiller will be purchased. If we agree to a purchase, the equipment scope, pickup arrangements, and payment terms are confirmed with the party authorized to sell.
Payment is made upfront before pickup on the agreed terms. Confirm what is included and the planned collection window before the work is scheduled. No particular price or transaction outcome should be assumed before the equipment and project have been reviewed.
To begin, provide the chiller’s location within the property, any available nameplate details, its known condition, and photographs that show both the unit and its route to a loading area. Note what is included in the sale, what must remain, and who can authorize access and explain site requirements. We can review those details and discuss whether the equipment and removal scope fit a purchase. You do not need to prepare the machine for operation or arrange a crane, recovery contractor, or hauler before reaching out.

Air-cooled or water-cooled. Centrifugal, screw or scroll. From single units to large shutdown projects, we buy industrial chillers across Texas.
Send us your chiller details and nameplate photos for a cash offer. Don’t worry if you don’t know every specification—we can start with what you have.
Call or text(614) 715-3047TEXT NAMEPLATE PHOTOS ↗Prefer email?
saleselectricalbuyers@gmail.com