SEND THE DETAILS
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We buy chillers marked R-22 in El Paso, Texas, with cash offers and upfront payment when a purchase is agreed. We handle removal, and the seller does not need to test the equipment.
From first photo to final haul, we take care of the details so you can move forward.
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We review the chiller and your site information, then make an offer. Payment is upfront.
We handle disconnects, refrigerant recovery, crane and rigging, loading, freight and hauling.
An R-22 label is a useful clue when describing a chiller, but it does not establish what refrigerant is in the machine now. A unit may have been serviced or altered, or its charge may be unknown. Share what the plate says and any records you have; there is no need to open a circuit, handle refrigerant, or verify the charge yourself.
We buy used industrial and commercial chillers, including units marked R-22, and consider equipment across refrigerants and a broad range of capacities. Idle and non-running machines can be reviewed. A purchase is not automatic: the equipment, available information, and removal project all matter to an offer.
Before discussing removal, identify the chiller and the items that belong with it. Photos of the overall unit, identification plate, refrigerant marking, and any included components can help. Note whether the machine is installed, disconnected, or in storage, and describe its known condition without guessing about internal parts.
Just as important, explain what must remain. A mechanical room may contain adjacent pumps, piping, electrical gear, controls, or other equipment that is not part of the sale. Marking the boundary in photos or drawings can help prevent confusion. Do not remove connected components or isolate utilities on the buyer’s behalf; those tasks are coordinated with the authorized site contact.
Cooling tons describe capacity, not the chiller’s weight. Photos and the nameplate are helpful starting points, but they do not replace assessment of the actual machine and the route out of the building.
Send the make and model if visible, stated capacity, serial or identification details, refrigerant marking, and current photographs. Include service, conversion, or decommissioning records if readily available. If records are missing, the label is unclear, or the unit’s history is uncertain, simply say so. You do not need to run, restart, repair, or test a chiller to have it considered.
Also identify who owns the equipment or is authorized to approve its sale, who can arrange site access, and any known deadline. A cash offer depends on review of the asset and actual project conditions; it is not guaranteed by a label, capacity, or photograph alone.
Removal planning begins with the chiller’s position and the path to a loading point. Tell us whether it is on a roof, on a pad, or inside a mechanical space, and describe doors, corridors, stairs, dock access, or yard routes that may affect movement. Photos from safe, accessible locations can clarify the approach.
Conditions vary from site to site. A narrow opening, limited staging area, overhead obstruction, floor-loading restriction, or nearby operating equipment may change the sequence or handling method. In El Paso, as elsewhere, the actual property layout and access rules—not assumptions based on the city—guide the plan. The authorized contact should identify site restrictions, approved work hours, security procedures, and any required approvals.
The seller does not need to vent refrigerant or open the chiller’s refrigerant circuit. If a purchase is agreed, we arrange appropriate recovery with qualified personnel and coordinate equipment disconnects with the authorized site representative. The current charge and configuration must be established through the project review; the R-22 marking alone cannot answer those questions.
We coordinate rigging, crane work when needed, loading, freight, and hauling as part of the equipment-side removal. The right approach depends on the machine and the site. The seller or facility supplies accurate information, authorized access, applicable site rules, and necessary approvals. If utilities or surrounding systems require facility-controlled isolation, that boundary and timing should be settled with the people responsible for them.
If both sides agree to a purchase, the included equipment, access plan, timing, and payment terms should be clear before pickup. Payment is made upfront before collection on agreed terms. The seller is not expected to hire a recovery contractor, crane, rigging crew, or carrier, or to deliver the chiller; we coordinate the removal work.
Gather a few current photos, the available nameplate and refrigerant information, a short description of condition, and the chiller’s location on the property. Add any known access limits and say who can authorize the sale and arrange entry. That gives us a basis to review the asset and removal scope without asking you to prepare or restart equipment.
If the unit is already disconnected or in storage, include that detail and explain what remains with it. The next step is a review of the information and project conditions, followed by discussion of whether a purchase and removal plan can be agreed.

Air-cooled or water-cooled. Centrifugal, screw or scroll. From single units to large shutdown projects, we buy industrial chillers across Texas.
Send us your chiller details and nameplate photos for a cash offer. Don’t worry if you don’t know every specification—we can start with what you have.
Call or text(614) 715-3047TEXT NAMEPLATE PHOTOS ↗Prefer email?
saleselectricalbuyers@gmail.com