SEND THE DETAILS
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We buy Carrier chillers in El Paso, Texas, with cash offers and upfront payment when a purchase is agreed. We handle removal, and the seller does not need to test the equipment.
From first photo to final haul, we take care of the details so you can move forward.
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We review the chiller and your site information, then make an offer. Payment is upfront.
We handle disconnects, refrigerant recovery, crane and rigging, loading, freight and hauling.
With a Carrier chiller, the nameplate helps identify the machine, but a workable pickup begins with its physical path to a truck. Consider the sequence from the unit’s current position to the building exit and loading area: what must be disconnected, where the equipment can be moved, and how it can reach transport. The route may be direct or may require careful planning around the facility’s layout. Share what is known; there is no need to assume a particular obstacle exists.
We buy used Carrier water-cooled and air-cooled chillers, including centrifugal, screw, and scroll units. We consider equipment from about 20 tons through 2,000+ tons, across refrigerants, and may review idle or non-running machines. A cooling ton describes capacity, not the chiller’s weight, so it cannot establish what rigging or transport the unit needs.
Start with the information already available: model and serial number, cooling capacity, chiller type, and whether the unit is installed, stored, idle, or known to be non-running. A clear nameplate photo and a few wider views can help distinguish the chiller from connected or nearby equipment. If labels are hard to reach, components are missing, or the machine’s history is incomplete, say so rather than putting anyone at risk to obtain more detail.
It also helps to identify the equipment being offered and anything that is not part of the sale. For a machine connected to shared plant systems, note which pumps, piping, controls, or other chillers must remain. An authorized site contact can clarify boundaries, operating restrictions, access rules, and any approvals needed before work begins. You do not need to prepare a full engineering survey to start a review.
Photos of the unit’s surroundings and the route toward the loading point are useful alongside the nameplate. Describe the truck entrance, check-in requirements, travel distance inside the site, and any limits on work hours or vehicle movement. Depending on the actual arrangement, clearances, doorways, overhead services, floor conditions, active operations, or a long internal route may affect the method and schedule. Flag known constraints early so they can be considered rather than discovered during pickup.
The route determines how the machine can be disconnected, rigged, moved, loaded, and hauled. We coordinate the removal scope with the authorized site contact and handle the equipment work, including appropriate refrigerant recovery by qualified personnel, disconnects, rigging, crane work when needed, loading, freight, and hauling. The handling plan depends on the chiller and the site; a crane or any particular access method should not be presumed in advance.
You do not need to start, test, repair, clean, or restart the chiller to ask whether it can be purchased. Non-running status is useful information, not a reason to run the equipment before review. Share what is known about its condition, configuration, and service history, including uncertainty. The purchase decision and any offer depend on the asset and the actual project review.
Do not vent refrigerant or open the circuit to check what remains. Current charge and refrigerant condition may be unknown until the equipment is assessed. If the machine is still connected to electrical, water, or shared plant services, describe that status and identify the person authorized to approve the necessary site work. Recovery and disconnect arrangements are coordinated as part of the removal when a purchase is agreed.
A cash offer is not guaranteed; it depends on the chiller, its condition and included components, and the work required to collect it. Before proceeding, the agreed terms should make clear which equipment is included, the pickup scope, access arrangements, and timing. If a purchase is agreed, payment is made upfront before pickup on the terms agreed with the seller. The site supplies accurate information, authorized access, applicable rules, and necessary approvals; equipment removal work is the buyer’s responsibility.
To begin, gather the nameplate details or a readable photo, images showing the machine and its route to the loading area, and a brief note on condition, connections, and known site limits. Include the location within the property and the authorized contact for access and approvals. That gives the buyer a practical basis to review the Carrier chiller and discuss whether an offer and coordinated pickup make sense—without asking you to run the machine or arrange recovery or hauling yourself.

Air-cooled or water-cooled. Centrifugal, screw or scroll. From single units to large shutdown projects, we buy industrial chillers across Texas.
Send us your chiller details and nameplate photos for a cash offer. Don’t worry if you don’t know every specification—we can start with what you have.
Call or text(614) 715-3047TEXT NAMEPLATE PHOTOS ↗Prefer email?
saleselectricalbuyers@gmail.com