SEND THE DETAILS
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We buy 100 to 249 ton chillers in Austin, Texas, with cash offers and upfront payment when a purchase is agreed. We handle removal, and the seller does not need to test the equipment.
From first photo to final haul, we take care of the details so you can move forward.
Share a nameplate photo, the location, and whatever you know about your equipment. No testing is required from you.
We review the chiller and your site information, then make an offer. Payment is upfront.
We handle disconnects, refrigerant recovery, crane and rigging, loading, freight and hauling.
If you have a 100–249 ton chiller to sell in Austin, Texas, begin with what you can confirm without running it. We buy used industrial and commercial chillers, including water-cooled and air-cooled equipment, and consider centrifugal, screw, and scroll units. Idle or non-running equipment may be reviewed too. You do not need to test, repair, or restart the machine to start a conversation.
Share the manufacturer and model if visible, the nameplate capacity, refrigerant information if known, and a few current photographs. Include the whole unit, its identification plate, and the surrounding area from safe vantage points. Note whether it is installed, disconnected, in storage, or missing components. If a label is unreadable or a detail is unknown, say so rather than guessing. A cooling ton measures capacity, not equipment weight, and should not be used to estimate lifting requirements.
We use the information supplied to review the asset and the work that a purchase would involve. Configuration, condition, refrigerant charge, equipment history, and surroundings are not established by capacity alone. Tell us what you know about operating status, prior modifications, leaks, or damage, but do not open the refrigerant circuit to investigate. We consider all refrigerants; the actual handling plan depends on what is present and the equipment’s condition.
Location within the property matters as much as the route out. Explain whether the chiller is at grade, on a roof, below ground, or inside a plant room. Photos or a simple description can identify stairs, doors, tight turns, overhead obstructions, nearby machinery, and possible staging areas. If the unit shares a room or connections with equipment that must remain in service, identify the sale boundary and any work limits.
Before a removal plan is settled, identify the person authorized to approve the sale and coordinate site entry. That contact can explain site rules, required approvals, security procedures, operating hours, and any restrictions on vehicles or work windows. At an Austin facility, scheduling may need to account for occupied areas, deliveries, or other activity—but the relevant constraints are the ones that apply to your property.
For a chiller being replaced, share the expected changeover timing and clarify which equipment is included. The outgoing machine may sit beside active plant or share services with equipment that stays behind. A facilities representative or project contractor can help define the permitted work area and handoff, so the removal plan does not assume that an entire plant is available to shut down.
Once the asset and site details have been reviewed, removal planning can address disconnects, recovery, rigging, loading, and freight. The practical method depends on verified dimensions and weight, the equipment’s position, the route, and the site’s conditions. A crane may be needed in some circumstances; other sites may have different lifting or staging constraints. Capacity alone does not determine the equipment or crew required.
We coordinate and handle appropriate refrigerant recovery with qualified personnel, along with the equipment work, rigging, crane work when needed, loading, and hauling covered by the agreed scope. Do not vent refrigerant or open the circuit. You are not required to hire a recovery contractor, crane, or hauler before seeking an offer. The authorized site contact provides accurate information, access, applicable rules, and necessary approvals.
A cash offer depends on the specific chiller and the project review, including its configuration, reported condition, and collection requirements. An offer is not guaranteed, and discussing a unit does not commit either side to a purchase. If we agree to buy it, confirm in writing which equipment is included, the payment terms, access arrangements, and the expected collection window before work is scheduled.
When a purchase is agreed, payment is made upfront before pickup, on the agreed terms. You do not need to run the machine to qualify for review or arrange the removal crew yourself. Make sure the person handling the transaction can authorize the equipment’s sale and coordinate with whoever controls access to the property.
To begin, gather the nameplate details you can read, current photographs, known condition, and a brief description of where the chiller sits and how it may be reached. Include refrigerant information only if available; do not disturb the system to find it. Mention known access limits and who can answer site questions. With those details, we can review the equipment and discuss whether a purchase and removal scope may be workable.

Air-cooled or water-cooled. Centrifugal, screw or scroll. From single units to large shutdown projects, we buy industrial chillers across Texas.
Send us your chiller details and nameplate photos for a cash offer. Don’t worry if you don’t know every specification—we can start with what you have.
Call or text(614) 715-3047TEXT NAMEPLATE PHOTOS ↗Prefer email?
saleselectricalbuyers@gmail.com